Italiano English Ctrl+P to print
Products: flash

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/variabili.adoc[]

FLASH: Instructions for use

254be91 10-05-2023 14:30:46 UTC +1

Offcarr

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/10_introduction.adoc[]

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/01_labelling.adoc[]

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/100_use.adoc[]

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/110_warnings.adoc[]

1. Product presentation

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/description.adoc[]

2. Preparation for use

Important The preparation for use of these devices must be performed by qualified personnel to ensure the specific suitability of the product for the user and the correct working order of all parts and accessories, as well as to provide clear instructions to the user.

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/12_setup.adoc[]

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/13_regolazioni.adoc[]

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/120_maintenance.adoc[]

2.1. Replacement of tyre and inner tube

2.1.1. Removing the tyre and inner tube

  • Deflate the wheel

  • Insert a special lever between the rim and the shoulder of the tyre so that when the lever is overturned, the side of the tyre comes out (fig. 1 and 2).

Tyre/tube disassembly 1

Tyre/tube disassembly 2

  • Insert another lever 100mm away from the previous point and repeat the operation (fig.3).

  • Slide the two levers along the circle to free the entire shoulder of the tyre.

Tyre/tube disassembly 3

  • Extract the inner tube, starting from the side opposite the inflation valve (fig. 4).

  • Once the inner tube has been extracted, it is easy to remove the tyre to replace one or both of them.

Tyre/tube disassembly 4

2.1.2. Assembling the inner tube and tyre

  • Insert the (partially deflated) bladder into the tyre (fig. 5)

  • Insert the chamber inflation valve into the hole on the rim.

  • Insert one side of the tire entirely on the rim, paying attention to the direction of the tire tread pattern depending on whether the push wheel is right or left.

  • Insert the opposite shoulder on the rim as well, starting from the point where the valve is positioned and continuing in both directions.

  • Insert the last part of the shoulder with the help of the special levers by following the instructions represented in Fig. 3, Fig. 2 and Fig. 1 backwards.

  • Inflate the wheel to the pressure indicated on the side of the tyre.

Tyre/tube assembly

2.2. Replacing rear wheel bearings

Disassembly

  • The bearings in the push wheels (B1 and B2) are press-fit. To extract them it is necessary to push them from the inside with the aid of an extractor or a pin punch and a hammer.
Bearings replacement

Assembly

  • Position the new bearing B1 on the inside of the hub so that it is coaxial with the hub and apply pressure to seat it.

  • Before positioning the second bearing B2 insert the axle A to use it as a guide for the second bearing and to ensure coaxiality of the system.

3. Technical service

For any service request, please contact OFFCARR supplying the following indications:

  1. Model

  2. Serial number

  3. Fault description

  4. Any reference or order number, if available, recorded on the order form.

  5. Dealer

Every component of the device is available as spare part.

4. Warranty terms

It is strongly advised to register the product on the website www.offcarr.com after delivery.

  1. The label showing the serial number, the manufacturer address and the CE symbol cannot be removed for any reason to preserve the warranty validity.

  2. Parts subject to normal wear and tear are not covered by the warranty, unless specific wear is caused by evident manufacturing fault.

  3. During the warranty period OFFCARR may proceed at its own discretion to change or to repair the faulty parts.

  4. The warranty does not cover damage due to negligence, carelessness, misuse or by incorrect maintenance performed by non authorized personnel.

  5. If any damage occurred during transport, the forwarder company is the only responsible. It is important to inform immediately both the forwarder company and, for information, OFFCARR.

  6. The warranty does not cover injury or any other damage to people or goods connected to the device’s malfunctioning.

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/160_packaging.adoc[]

Unresolved directive in flash.adoc - include::../lingue/en/modelli/flash/170_disposal.adoc[]















OFFCARR s.r.l. reserves the right to make improvements and/or changes on its products, at any time without prior notice, with respect of the device features, suitability, certifications, warranty contract and availability of spare parts according to the terms of law.













UMFLA_L_IT-R1 - Edizione 01-2021